|
|
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
WRAC badge
Good evening,
I need your advice about this WRAC badge. Thank you |
#2
|
||||
|
||||
WRAC badges are normaly sliders as the Beech Brown Badge Backing has a built in pocket for it. Looks to me to be a Officers Collar Badge as only Officers wear them.
|
#3
|
||||
|
||||
Thank you for your reply
I think you are right about the collar badge. It is only 4 cm high, too small for a cap badge |
#4
|
||||
|
||||
The original (1950) badges were lugged as yours is, shanks were added c1954. I have never seen this pattern used as a collar badge.
Officers Collar below. Marc
__________________
I am still looking for British Army cloth Formation, Regimental, Battalion, Company and other Unit sleeve badges, from 1980 onwards. Last edited by 54Bty; 09-02-22 at 05:33 PM. |
#5
|
||||
|
||||
The ORs collar is the same, usually in gold anodised.
|
#6
|
||||
|
||||
Only to be worn by WO1's.
Marc
__________________
I am still looking for British Army cloth Formation, Regimental, Battalion, Company and other Unit sleeve badges, from 1980 onwards. |
#7
|
||||
|
||||
WRAC QC gold anodised collar badges and officers QC and KC gilt badges:
Tim
__________________
"Manui dat cognitio vires - Knowledge gives strength to the arm" "Better to know it but not need it than to need it and not know it!" "Have more than thou showest, speak less than thou knowest." |
#8
|
||||
|
||||
In 1972/73 I picked up half dozen WRAC bimetal badges at a junk shop in Lee, SE London, a King's Crown lugged and some St Edward's Crown slidered. One of the slidered was exchanged with a WRAC in 'Derry for an anodised aluminium version.
It took me until a couple of years ago to get around to getting a slidered bimetal King's Crown badge, it came on a named, 1963 dated beret. The badge fitting is different to the norm in berets, not consisting of a sewn on pocket on the inside of the headgear. Presumably the lugged badges weren't considered suitable for use on women's headgear, the cotter pin being liable to catch in the hair and the style of badge fitting is an extension of this consideration. |
#9
|
||||
|
||||
Both the QC and KC officer's gilt collars in my WRAC collection, have solid flat backs (die-cast?) - I'm assuming the one's Tim shows are the same construction. They look the same from the pics! However, I also have a pair of gilding metal (definitely not gilt) KC collars that are die-stamped. In light of this thread would they then only be worn by a WO1 and possibly with just an ordinary bi-metal cap badge?
Thanks Mark |
#10
|
||||
|
||||
I came back to correct myself on the main design of Officers Collar, but see I have been beaten to it
Re Other Ranks Collar badges - 'most' WRAC' are seconded to other Corps in their given trade and wear a Regimental collar badge of the Regiment/Corps above the left breast pocket. I remember many such WRAC wearing RAOC badges while in service. What 'regimentally employed' WRAC at Gilford wore I do not know. At Bicester in the early 70's we had a WRAC CSM who wore a RAOC collar badge, and I must admit I cannot remember what the attached WRAC WO1's (of which we had a few at Bicester) wore on No2 dress, but they did wear a RAOC badge on the green pullover. Last edited by Mike_2817; 09-01-19 at 08:19 PM. |
#11
|
||||
|
||||
Quote:
Andy
__________________
Leave to carry on Sir please. |
#12
|
||||
|
||||
No - they scared me, especially the RMP ones - small, but incredibly vicious.
|
#13
|
||||
|
||||
Quote:
|
|
|